Choosing Upvc Window Replacement Hinges
The process of selecting and fitting upvc window hinges for replacement isn't as difficult as you might imagine. Make sure that the arrows on the hinges face in the correct direction, and then measure the thickness of the hinge arms on the frame that opens (13mm or17mm).
There are many different kinds of hinges to pick from, each with distinct characteristics. This article will discuss the most popular kinds of uPVC window hinges and the advantages they offer.
Egress/Easy Clean Hinge
They are a great option for replacing or upgrading a fire escape safety window because they can be opened at a 90-degree angle. They can be disengaged to an easy-clean position that allows you to see the windows' exterior without having to climb ladders or lean at dangerous angles.
These heavy duty egress hinges are manufactured by Yale, one of the most popular and trusted home security brands on the market today. They can be used with all types of uPVC side-hung windows. By pressing a small button the window sash can be slid to the side and then into the clean position. After closing, the sash will be reset to its initial position.
They are available in both 13mm and 17mm stack heights. Utilize our Egress Selection Guide to help you determine the best product for your window.
These hinges can be fitted to standard side-hung frames made of uPVC, or aluminium. The friction screw is used to adjust the resistance. This makes it easier to open the window and reduces the risk of an accidental closure during strong winds. They have been tested for over 30,000 cycles, and comply with British Standards approved BS EN 130126-6:2008 and BBA/Secured by Design.
Without buttons or catches, There are no buttons or catches. Nico Egress Easy Clean Friction Hinge is easy to use and offers a practical solution for emergency egress and secure cleaning. Press the hinge retention clip located in the inner corner of the bottom corner. This will release both the top and bottom catches and allow you to slide the sash to the clean position. Once it is in the easy-clean position, close the window to reset the hinges to their egress positions.
Fire-Escape Hinge
Fire Escape Hinges are often referred to as "Easy Clean" hinges are used to replace windows that open sideways to allow egress (fire safety) reasons. They allow for more space in the event of a fire. This type of hinge is legal in any room with a window as stipulated by building regulations.
The windows have a friction stay that allows them to open at 90 degrees. They also allow the opening sash slide across the glass when it's opened, allowing for simple cleaning without the need to climb ladders. The hinges have no fiddly buttons or catches and are operated with an easy, secure lever that is accessible from inside the home.
The hinges are made in the UK by Cotswold and come with a child safety restrictor for day to day use that can be overridden with a hidden button providing you with peace of mind that your children will not accidentally open the door too far. The stack heights are 13mm or 17mm.
To order these hinges, simply take a measurement of the length of your existing side-hung window hinge which is fixed to the frame (see the article on measuring your upvc window hinges). Select the correct size hinge below.
Note that this measurement is taken from the hinge's point that is attached to the frame and not the sash. The actual hinge length can be longer or shorter depending on how your windows were made in the past. When choosing the width of your hinge, the majority of upvc windows can be fitted with a 13mm stack height but should your old window frame has 17mm, then select the option for this. Alternately, you can install the 4mm packer to make up for the difference. All the hinges are supplied handed (1 left and 1 right). The hinges do not include screws. If needed, they can be purchased separately. Our upvc window repair screws are recommended. These screws are designed to increase your hinges' performance and allow them to operate smoothly for longer. They have a reduced friction design and an improved weather seal with a new nylon reducer cap.
Restricted Hinge
There are times when windows must fully open and this can be a challenge using a standard hinge. These child safety friction hinges are a great solution to this problem. They can be used when ventilation is required, but escaping or cleaning a fire is not feasible. They restrict the amount of opening the sash, and allow for the bypass of this limitation by pressing a button. They work with both top and side hung windows and come in 13mm and 17mm stack heights.
The Nico Restricted Egress Friction Hinges blend the features of both a standard restrictor and a fire escape pivot to provide a simple but efficient way to meet building regulations. It is available in 13mm or 17mm stack heights and is suitable for both top and side opening uPVC window. It is supplied as a pair of hinges where one hinge is restricted egress and the second is unrestricted allowing one of these to be placed on the bottom of the sash while the other is fitted to the top.
These uPVC hinges are restrictive and have been tested to BS6375 Part 2. They are intended for use on a window that cannot be fully opened like a small children's bedroom. The mechanism restricts the amount the sash can open up to 100mm for safety and re-engages when the window is closed.
These uPVC friction-type hinges can be used with all types of windows. They are particularly useful for windows that are hard to reach, such as those in three-storey houses or those that require ladders. door repair hinge can be paired with our range of security enhancements like hinge guards and protection plates, or dog bolts for PAS 24 performance.
It is crucial to take measurements of the hinge on your current window to be able to find replacements of the same size. The most efficient method to do this is by viewing the hinge in the image gallery and determining the location you would like it to be. The top-hung hinges can only be positioned on one side, while the side hung hinges can only be placed on one side.
Standard Hinge
A standard hinge is made of metal-to-metal contacts and has no additional parts to reduce friction. It's available in a range of finishes and fire-rated. For a quick way to determine the radius of your hinge, lay it flat and align the quarter and dime in two corners. If the quarter is more snug than the corner, then it should be round to 5/8 inches.
The hinge you choose can enhance or break the appearance of your door. It's essential to match the style and finish of your door with the hinges to create a seamless design that is both practical and visually appealing.